Product Data Sheets

Recommended use:
Particularly suitable for brush application, can be spray applied.

Product features

General product information

Shelf life (months): 12

Storage temperature: Minimum 5°C Maximum 35°C, Minimum 40°F Maximum 94°F

Pack size: 1, 2.5 litres

Colour: Full colour range to order

Appearance when dry: Full gloss 95% (on a 60% head)

Curing: Air drying

Pot life (at 20°C, 68°F): N/A

Product specification

Volume solids: 47 ± 2%

VOC (g/l) 400 (varies with colour)

Weight per litre: 0.92 - 1.15 kg

Dry film thickness: 30-50 (microns)

Surface preparation

All surfaces should be clean, dry and free from all contaminants.
Normally applied over primer or undercoat.

Application

Mixing: Ensure product is stirred thoroughly before use.

Application methods:
Brush: ready for use.
Conventional spray (cold): Thin 10-15% with TN07.
Hot spray maximum: 70° Celcius, 158° Fahrenheit, Add thinner TN07 as required.

Thinning solvent: TN07

Curing/drying:
Touch dry: 4 hours 2 hours 1 hours
Hard dry: 12 hours 6 hours 3 hours
Overcoat time: 16 hours 16 hours 16 hours

Note: All information relates to typical dry film thickness.
Overcoating information: As above.

Recommended use:
High opacity brush or spray applied undercoat for use with Tekaloid SE and other single pack coach enamels

Product features

General product information

Shelf life (months): 24

Storage temperature: Minimum 5°C Maximum 35°C, Minimum 40°F Maximum 94°F

Pack size: 1 and 5 litres

Colour: Dispensed

Appearance when dry: High sheen

Curing: Air drying

Pot life (at 20°C, 68°F): N/A

Product specification

Volume solids: 47 ± 2%

VOC (g/l) 420 (as supplied - varies with colour)

Weight per litre: 1.2 - 0.05 kg

Dry film thickness: 30 - 45 (microns)

Wet film thickness: 64 - 96 (microns)

Surface preparation

All surfaces should be clean, dry and free from all contaminants.
Designed for use on commercial, public service vehicles after suitable preparation and priming.

May also be applied to aged finishes if they are in sound condition and suitably prepared.

Application

Mixing: Ensure product is stirred thoroughly before use.

Application methods:

Brush: ready for use (thin with TN07 if required)
Conventional spray - Thin 10% (35 secs BSB4) TN07.
Hot spray - ready for use (maximum 70° Celcius, 158° Fahrenheit)

Thinning solvent: TN07

Curing/drying:
Temperature 10°C 20°C 30°C
Touch dry: 4 hours 2 hours 1 hours
Hard dry: 8 hours 4 hours 2 hours
Overcoat time: 8 hours 4 hours 4 hours

Note: All information relates to typical dry film thickness.

Features and uses:
This product is formulated using a traditional long oil alkyd resin which has excellent adhesion properties along with the flexibility required when used on a range of different surfaces. It is designed for use on new steel, GRP, factory applied finishes and timber after suitable preparation.

Product information

Resin type: Long oil alkyd

Appearance when dry: Slight sheen

Colour availability: Grey

Volume solids (noninal): 39.0 ± 2%

Dry film thickness: 25 (microns)

Theoretical spreading rate: 15.6 m²/litre

VOC gms/litre as supplied: 390 (less water)

Shelf life: Best before 24 months

Storage conditions: Above 5°C, below 35°C, 40°F - 94°F

Weight per litre: 1.37kg

Pack size: 1, 2.5 and 5 litres

Flash point: Above 32°C, 87°F

Curing: Air drying

Surface preparation

All surfaces should be clean, dry and free from all contaminants.

Application details

Mixing: Ensure product is stirred thoroughly before use.

Conventional spray: 30 secs ± 5 Ford F4 cup (thinner TN02)

Curing/drying:
Touch dry: 4 hours 2 hours 1 hours
Hard dry: 12 hours 8 hours 4 hours
Overcoat time: 24 hours 16 hours 16 hours

Additional information: Aluminium and Zinc coated steel should be primed with Tekaloid etch CA42 or CA75.

Features and uses:
This product is a brushing filler for small imperfections. It is based on a fast drying, modified alkyd with good sanding and filling properties. It is designed to be applied either in a single of multiple coat. It can be sanded down and re-coated after 4 hours. It is designed to be top coated with a wide range of single componant finishes and udercoats but is specifically designed for the Tekaloid range of coach finishes.

Product information

Resin type: Modified alkyd selected pigment

Appearance when dry: Matt

Colour availability: Grey

Volume solids (nominal): 41 ± 2%

Dry film thickness: 50 (microns)

Theoretical spreading rate: 8.2 m²/litre

VOC gms/litre as supplied: 507

Shelf life: Best before 12 months

Storage conditions: Above 5°C, below 35°C, 40°F - 94°F

Weight per litre: 1.49kg

Pack size: 1 and 5 litres

Flash point: Above 32°C, 87°F

Curing: Air drying

Surface preparation

All surfaces should be clean, dry and free from all contaminants.

Application details

Mixing: Ensure product is stirred thoroughly before use.

Curing/drying:
Touch dry: 1 hour 30 minutes 15 minutes
Hard dry: 4 hours 2 hours 1 hour
Overcoat time: 8 hours 4 hours 2 hours

Additional information: Apply in successive layers either wet-on-wet to a maximum of 80 microns, dry film, or allow to harden and re-coat as required with other coats if necessary.

Usage:
Protective primer for use on bare metal, Cast iron and steel.
Aluminium requires etch priming prior to application.

Application

Drying time: Touch dry 1 hour at 18°C, 63°F
Re-coat in 2 hours.

Appearance

Dry film thickness: Approx 25 microns per coat

Thinner: Standard TN07 Fast TN02

Features and uses

Application

Drying time: Touch dry 1 hour at 18°C, 63°F
Re-coat in 2 hours.

Appearance

Dry film thickness: Approx 25 microns per coat

Thinner: Standard TN07 Fast TN02